Beijing Ruiyixing Technology Co., Ltd.ccve365@qq.com·(010) 6053 0441·中文
RyCCVE365Request a quote
Technical articles ·

How to Select a Rack-Mount Power Supply

KEY TAKEAWAY

Pick a rack-mount power supply by voltage class, channel count, power headroom and 1U/2U size. Includes a comparison table of all models in the range.

A rack-mount centralized power supply is the standard power-distribution architecture for security and surveillance low-voltage systems: 19-inch rack installation, multiple independent output channels, and a dedicated fuse on every channel. This article covers selection by voltage, channel count, power, and mounting, and lists all 21 rack-mount models currently in stock for comparison.

1. What is a rack-mount centralized power supply?

Rack-mount supplies install in standard 19-inch racks, with height measured in rack units (U): 1U ≈ 44 mm (space-saving, suited to small and mid-size systems) and 2U ≈ 88 mm (better heat dissipation, suited to high channel counts and high power). Each output channel is independent, with its own fuse (some models use self-resetting PTC fuses) and status indicators, so a single unit can distribute power to front-end devices such as surveillance cameras, access-control equipment, and PTZ domes — replacing scattered individual power adapters.

Note: Our rack-mount supplies cover five output-voltage classes: DC12V (bullet and dome cameras), AC24V (high-speed PTZ domes), DC36V (PTZ speed domes), DC48V (PoE switches and telecom equipment), and DC5V (routers and fiber-optic transceivers). See the full list below.

2. Four selection factors: voltage, channels, power, and mounting

2.1 Voltage — set by the load devices

Bullet and dome cameras typically run on DC12V; high-speed domes and other pan-tilt equipment usually need AC24V or DC36V; PoE switches and fiber-optic transceivers commonly use DC48V; low-voltage devices such as routers use DC5V. The supply voltage must match the nameplate rating of each front-end device — never mix voltage classes on one load.

2.2 Channel count — match the number of front-end devices

Each independent output channel feeds one device (one fuse per channel). If you have N devices in total, choose a supply with at least N channels; leave a few spare channels for future expansion.

2.3 Power — leave 20–30% headroom

Total power = Σ (power draw of each device). Calculate the total load first, then choose a model rated 20–30% higher to avoid sustained full-load operation.

2.4 Mounting — 1U or 2U?

Choose 1U when rack space is tight. For 16 or more channels or total power of 500 W and above, choose 2U — heat dissipation and wiring have far more room.

3. Product list (grouped by output voltage)

Output voltageModelChannels / powerForm factor
DC12VPS-DC1208 series: 1U, 8 channels, 150 W8 channels / 150 W1U
PS-DC12 58A: 2U, 10 channels, 700 W10 channels / 700 W2U
PS-DC1241-32: 2U, 32 channels, 500 W32 channels / 500 W2U
2U, 16 channels, self-resetting fuses16 channels / self-resetting fuses2U
PS-DC1208-1U: 8 channels, 100 W8 channels / 100 W1U
PS-DC1220-1U 20A20 A / camera modules1U
PS-DC1216-8-1U: 12 channels, 200 W12 channels / 200 W1U
PS-DC1229-16A-2U: 16 channels, 350 W16 channels / 350 W2U
1U centralized access-control power, 25 ACentralized access-control power, 25 A1U
PS-DC1216-10A-2U for access controlAccess control: 8 × 1.25 A + 2 × 2 A2U
PS-DC1248-24-2U: 24 channels, 600 W24 channels / 600 W2U
PS-DC1225-1U 25A25 A / camera modules1U
PS-DC1229-8-1U: 8 channels, 29 A8 channels / 29 A1U
PS-DC1208-1U exampleExample: 1U, 8 channels / 100 W1U
AC24VPS-AC2425-16A-2U: 16 channels16 channels (PTZ domes)2U
1U AC24V8A: 8 channels8 channels / AC24V 8 A1U
2U AC24V16A: 10 channels10 channels / AC24V 16 A2U
2U AC24V25A: 10 channels, 600 W10 channels / 600 W2U
DC36VPS-DC3616-16-2U: 16 channels16 channels2U
PS-DC3625-16-2U: 16 channels, 900 W16 channels / 900 W2U
DC48VDC48V: 16 channels, 2U16 channels / 100–700 W2U
DC5VDC5V: 10 channels, 1U10 channels (routers / fiber-optic transceivers)1U

Source: specifications of 21 in-stock rack-mount models from our product database.

4. FAQ

Q: Can 1U and 2U units be mixed in one installation?
A: Yes. Mount them in the same rack grouped by voltage — DC12V and AC24V loads each connect to their matching supply.

Q: Can rack-mount supplies power access-control systems?
A: Yes. We offer dedicated centralized access-control models, whose DC12V output feeds card readers and electric locks from one central supply.

Q: How do I estimate total power quickly?
A: Sum the power draw of every device, then multiply by 1.2–1.3 to size the supply.

Need a model matched to your project?

Send the voltage class, device count and total load — we will confirm the model and the power headroom.

Request a quote